Watercolor for Beginners: Washes, Wet-on-Wet and Layers
Learn to control water and pigment in watercolor from zero: lay flat and graded washes, read the paper to choose wet-on-wet or wet-on-dry, glaze light to dark and mix clean colors. You finish by planning and painting a simple landscape of your own.
- Language
- English
- Lessons
- 6
- Minutes
- 150
Price: · The subscription includes the whole catalog at no extra cost.
Course outline
Water Control: Your Washes
- Your First Flat Wash: Paper, Water and Consistency (25′)
- Graded Washes: Painting a Sky (25′)
- Wet-on-Wet and Wet-on-Dry: Reading the Paper (25′)
Layers, Color and Your Landscape
- Layering Light to Dark (25′)
- Mixing Clean Colors (25′)
- Your First Landscape (25′)
Free first lesson
Your First Flat Wash: Paper, Water and Consistency
What you control: water and pigment
Besides tape and a rigid board (step 1 below), your student set, two round brushes, 140 lb paper, two jars of water and a paper towel or old rag for blotting are everything this first session needs. Use the brush, not your lips, to shape the tip: some pigments are not safe to swallow. In watercolor you do not really control the color; you control how much water travels with it. The same pan of blue gives a whisper of sky or a near-black shadow, and the only variable is the water-to-pigment ratio.
Painters name three consistencies, each with its job:
- Tea: watery and faint, for the lightest tints.
- Milk: the workhorse — flat washes are made of it.
- Cream: thick and slow, for dark details later on.
A flat wash is one even tone across a whole shape. Why use milk rather than tea for your first flat wash?
Set up and mix tea, milk and cream
- Find a rigid board larger than your sheet — an old baking sheet or the back of a picture frame works.
- Press painter's tape on your clothes a few times to weaken the glue, then tape the quarter sheet to the board on all four edges: taped paper dries flatter and buckles less.
- Fill both jars: one is your rinse jar, the other stays clean for mixing — dirty water turns washes gray.
- Mix tea: wet the brush in the clean jar, touch the paint once, swirl it into a puddle in the pan lid until it is a faint tint.
- Mix milk: pick up more pigment until the puddle lightly hides the lid's color beneath it.
- Mix cream: use only a little water and work plenty of paint into it until it is thick and slow.
- Paint a labeled swatch of each on scrap paper and keep it for checking future mixes.
The question above: tea dries so pale that you can hardly see whether your wash came out even, and its extra water pools and blooms more easily. Milk gives a clear mid tone that shows your control — tea washes come later, for the palest skies.
The wet bead: your wash's engine
A flat wash comes out even because one continuous wet bead does the work. Load the brush with milk and draw a stripe across the top of the sheet: liquid gathers in a bead along its lower edge. While that bead stays shiny, every stroke you feed into it joins everything before it as one pool.
Tilt the board slightly, top higher, so gravity pulls the bead down instead of letting it pool. When the shine leaves the bead, the wash is setting: new paint no longer joins it. Why does the wash streak if the bead dries halfway down the sheet?
Your first flat wash, step by step
Run the wash once on a strip of scrap paper before your good sheet.
- Prop the board at about 15 degrees, top higher.
- Load the brush fully with milk — a half-loaded brush breaks the bead partway across.
- Lay one steady stripe across the top, left to right.
- Reload quickly and lay the next stripe just below it, touching the bead so it feeds.
- Work down without pausing; each stripe pulls the same bead along.
- At the bottom, squeeze the brush nearly dry and lift the last bead with it, so no dark line dries at the tape edge. Leave the sheet flat until bone dry, and peel the tape off slowly at a low angle, away from the painting, so it does not tear the paper.
The streak answer: strokes made after the pause land on setting paint and stop blending into the pool.
Halfway there: a wash that starts to dry
Same strip, fresh start, and this time you decide. You have covered the top third when you run out of mixed paint. By the time more is mixed, the bead along your last stripe has lost its shine. Two thirds of the strip are still bare.
Do you feed the new paint into the setting wash, or stop? Decide before reading on.
Three ways a wash goes uneven
- Letting the bead dry mid-wash — the top cause of streaks. Reload before the shine leaves; if it leaves anyway, stop.
- Using a puddle too small or too watery — running out mid-wash breaks the bead, and extra water pools into blooms; mix more milk than you think you need.
- Going back to fix a setting wash — stirring it makes blotches. Wait until bone dry.
Keep these three
- Milk is the easiest consistency to read a first flat wash in; tea for faint tints, cream for dark details.
- One shiny bead kept moving top to bottom makes the wash even.
- Shine gone means setting: stop and let it dry.
Your wash on the quarter sheet
On your taped quarter sheet, lay one flat wash in milk from top to bottom, keeping the bead alive until you lift it at the last edge. Let it dry untouched, then judge it against window light.
- Wash
- A thin layer of watercolor, water and pigment together, spread to cover a whole area of paper.
- Flat wash
- A wash that dries as one even tone across the whole area, with no streaks, stripes or blotches.
- Consistency
- How much water versus pigment is in your mix: tea (faint and watery), milk (the workhorse for washes) or cream (thick, for dark details).
- Wet bead
- The shiny ridge of liquid that gathers at the lower edge of wet paint; while it stays shiny, each new stroke joins the wash as one pool.