Basic Bike Maintenance: Fix a Flat, Lube the Chain, Adjust Brakes
Run a quick pre-ride safety check, take a wheel off and patch or replace a flat tube, and clean and lube your chain. You'll also take up slack in rim or mechanical disc brakes, center them, verify them with the walk test, and know when a problem is a job for a bike shop.
- Language
- English
- Lessons
- 6
- Minutes
- 150
Price: · The subscription includes the whole catalog at no extra cost.
Course outline
Before you ride
- The pre-ride check on your own bike (25′)
Fixing a flat
- Get the wheel off and find the puncture (25′)
- Patch or replace the tube and refit the wheel (25′)
A clean chain
- Clean and lube your chain (25′)
Brakes you can trust
- Adjust brake cable tension (25′)
- Center the brakes and do the walk test (25′)
Free first lesson
The pre-ride check on your own bike
A two-minute check, every ride
Your bike leaning by the door is the one you'll check, so start there. Before every ride you'll run the same four checks in the same order: air, brakes, cranks, quick releases. The order matters less than never skipping one — each item catches a failure that either strands you far from home or keeps you from stopping. Air comes first because a soft tire causes the most common roadside problem of all: the flat.
Why does a soft tire matter even before it goes flat?
Air: the sidewall has the number
A soft tire isn't just slow. When you hit a curb or pothole, the rim can squeeze the tube against the ground hard enough to cut it — a pinch flat, and it happens far more often to underinflated tires. The number you need is printed on the sidewall of your tire, the rubber side, as a range like "inflate 50–80 psi". Psi is pounds per square inch, the unit your pump gauge reads.
Find your own range now. While you're looking, check the tread and sidewall for cuts, bulges or threads showing through the rubber: a bulge or a cut you can see the tube through is a no-ride finding and a new tire. Then press the gauge firmly onto each valve — front first, then rear — and read it. Aim for the middle of the range.
Why isn't squeezing the tire enough? Because a tire at half its pressure still feels firm to a thumb. Only the gauge can tell 40 from 60 psi.
Brakes, cranks and quick releases
Squeeze each brake lever hard, standing still. The pads should grip the rim — or the rotor, the steel disc at the hub — while the lever is still a thumb's width from the handlebar. If the lever feels spongy or reaches the bar, that brake needs adjusting before you ride. That's a no-ride finding, and taking up cable tension is exactly what a later lesson teaches. Also look at the pads: if their grooves are worn away, they need replacing, not adjusting. On hydraulic disc brakes (a hose instead of a cable) a spongy lever means air in the system — that's a shop job.
Grab each crank arm, the arm the pedal attaches to, and rock it sideways: no clicking, no wobble. If one clicks or moves, that's a no-ride finding for a bike shop — a loose crank can work its way off.
Last, the quick release — the lever on each wheel's axle that clamps the wheel into the fork or frame without tools. (If your bike has thru axles instead, check each one is fully tightened or its lever firmly closed.) It should take a firm push to close, firm enough to leave a mark in your palm. Why does it need to hurt a little? Because clamping the wheel solidly is its whole job: a lever that opens with two fingers isn't holding the wheel, and a wheel can shift under braking.
The check on a bike like yours
Here's a full run on a commuter hybrid, the kind of bike many people start on:
- Sidewall reads "inflate 50–80 psi". Front tire: gauge says 35. Rear: 55.
- Front pumped to 65 — the middle of the range.
- Both levers bite a thumb's width from the bar.
- Cranks rock sideways: silent.
- Quick releases: each took a firm push and left a mark.
One finding — the soft front tire — fixed on the spot with the pump you already own. And notice: that front tire had felt almost normal to the squeeze. The gauge caught what the thumb couldn't.
Read these findings yourself
Now you read the findings. A different bike, same check:
- Sidewall says 50–80 psi; the rear gauge reads 70.
- The rear brake lever comes almost to the handlebar.
- The rear quick release swings open with two fingers.
Your turn: which of these are no-ride findings, and which is fine? What gets fixed before this bike is ridden?
Three ways this check goes wrong
- Trusting the thumb over the gauge. A tire at half pressure still feels firm; confirm with the gauge against the sidewall range.
- Riding on a spongy lever, planning to brake early. At speed or in the wet, a lever that reaches the bar won't stop the bike in time.
- Half-closing a quick release. The lever must point fully closed and take a firm push, or the wheel can shift under braking.
Keep these three
- Air: the gauge reads inside the sidewall range — feel lies.
- Brakes: the lever bites a thumb's width from the bar, or the bike stays home.
- Quick releases: firm to close, leaving a mark in your palm.
Run it on your bike
Run the full check on your own bike now: air, brakes, cranks, quick releases. Write down the pressure range on your sidewall, both gauge readings, and every no-ride finding you discover.
- Sidewall
- The rubber side of the tire, where the recommended pressure range is printed.
- Psi
- Pounds per square inch, the pressure unit your pump gauge reads.
- Pinch flat
- A puncture caused by the rim pinching an underinflated tube against the ground, typically on a curb or pothole.
- Quick release
- The lever on a wheel's axle that clamps the wheel into the fork or frame without tools.
- No-ride finding
- Any check result that means the bike should not be ridden until it is fixed.
- Crank arm
- The arm the pedal attaches to.
- Rotor
- The steel disc at the hub that disc brake pads grip.